Here for Railgun. Season 4 let’s goooo

Ah yes, that one scene in Monsters Vs Aliens

They used the wrong magic word 🚓👮‍♂️👮‍♀️

Same expression too, I assume?

What does paper ballot mean if it’s all electronic? When I voted, I filled a bubble with black pan and stuck the ballot in an oversized Scantron machine

What are you an accessory to? Murder? On the dance floor?

I just bought a drone, hopefully it arrives by this weekend and I’ll start posting some pictures

Edit: it did not

I know right? They are super good for that and I still haven’t managed to get my hands on one of the ones with a USB cable because of what people are charging for them used now.

3D printers are easier to use than getting ink on paper and it’s appalling

Bit discouraging tbh

Only reason they can imagine you haven’t logged in in a month.

Why did Best Buy survive buy Circuit City went under? They were basically the same thing, so what did they do differently?

Reader Mode usually works to bypass paywalls that just blur the text like that.

Edit: oops I’ve removed the article text

Well gee wiz, so that’s where it went

Hey I just saw your update! I’m glad you’re getting better results, but like you mentioned, something is definitely still wrong. I’m still pretty convinced your nozzle is clogged, even though it’s new, and I’ll do my best to explain why!

To start, if your printer wasn’t working normally before you printed in wood, I’m totally wrong about everything below and you can stop reading here!

If your printer was working normally before you tried printing in wood though, that means the e-steps were already calibrated correctly, and they wouldn’t need to be re-calibrated after replacing the hot end. If you had replaced the extruder and it started acting this way, that would be a good reason to re-calibrate the e-steps, but replacing the hot-end shouldn’t have had an impact. After swapping an extruder, you calibrate e-steps to basically teach the printer how to extrude the correct amount of filament in the real world again since the new extruder might have different specs from the original and the printer has no way to know something has changed. A hot-end swap doesn’t necessitate recalibrating e-steps though because the extruder is the same and it’s still going to be pushing the same amount of filament through the printer.

If your nozzle is clogged and you recalibrate the e-steps, the measurements you take will be off since the printer can’t push filament through at the rate it should be able to. Your new benchy looks better than before, but that could be because the higher e-steps you calculated mean the printer is now forcing more filament past the blockage by working the extruder more. It’s been calibrated to compensate for the fact it can’t push filament through fast enough, but it’s working harder to do this and it will severely limit its speed before it starts underextruding again. I’m guessing this is the reason for the 3 hour long benchy at 20mm/s? You shouldn’t need to be at 220 C to get PLA to print at 20mm/s from a 0.4mm nozzle either.

Not all nozzles or hotends are well-made or handled with care at the factory. It’s totally possible you got one that shipped with some sort of tiny unnoticeable debris inside that worked its way down into the nozzle as the filament pushed it along. I have a cheap bag of 0.4mm nozzles that have metal shavings stuck in some of them and your first benchy is exactly what my prints look like when I use one of them. If possible, I still recommend changing the nozzle before doing anything more expensive like replacing the extruder. You’ll probably need to set the e-steps back to what they were before changing them though, otherwise you’ll be extruding too much filament if the new nozzle isn’t clogged and the old one is.

Man, I honestly love the name okidogi though

This is the first time I’ve even heard the idea of Japan being a “liberal paradise”. I thought it was widely know Japan was super conservative.

I would simply fire up the ol’ 3DS (the best handheld console) and revisit any Pokemon game from Red and Blue to Ultra Sun and Ultra Moon.

Must be one of them hentais